Shanghai Rotorcomp Screw Compressor Co., Ltd.
  • Máy nén trục vít quay Nhà sản xuất nổi tiếng nổi tiếng sản xuất máy nén trục vít chất lượng, máy nén dầu không nén, máy nén áp lực cao trong ISO, TUV, CE giấy chứng nhận với giá tốt, 5 năm bảo hành, thiết kế độc đáo cấp bằng sáng chế, tiết kiệm năng lượng, đáng tin cậy máy nén Máy nén trục vít quay
  • Máy nén khí không dầu Thượng Hải rotorcomp máy nén trục vít cung cấp 100% dầu sạch dầu máy nén miễn phí có thể được làm trong không khí làm mát và nước làm mát, chúng tôi có thể tùy chỉnh theo yêu cầu đặc biệt, và dịch vụ OEM ... Máy nén khí không dầu
  • Hệ thống xử lý không khí Thiết bị xử lý sau nén của nhà chế tạo compressorISO, CE, TUV, ASME sản xuất chất lượng máy sấy không khí lạnh, máy hút không khí khô, bộ lọc đường ống từ 1micron đến 0.001micron, xe hoạt động ... Hệ thống xử lý không khí
  • Máy nén khí trục vít di động Máy nén khí trục vít động cơ diesel Máy nén khí di động dẻo dẻo dẻo nhà sản xuất sản xuất máy nén trục vít diesel chất lượng từ 50cfm - 1600cfm @ 100psi-500psi trong ISO, TUV, giấy chứng nhận CE với p tốt ... Máy nén khí trục vít di động
  • Screw Air End SCREW AIR ENDWPhụ kiện máy nén trục vít không gỉ hàng đầu thế giới với hiệu suất tốt nhất trong các tiêu chuẩn ISO, TUV, 5 năm bảo hành.Rotorcomp bơm dầu không khí tạo thành trái tim ... Screw Air End
CONATCT
Tel: + 86-021-67150020
Fax: + 86-021-67150020
Thêm: No.28 Minta Road, Quận Songjiang Thượng Hải, Trung Quốc
code

Thất bại và Nguyên nhân Điện thường gặp

Bản đánh giá lỗi này
Ngừng thất bại gây ra bởi các bộ phận bên ngoài của bộ điều khiển có thể bị xóa bằng cách kiểm tra Lỗi NÀY hoặc HISTORY FAULT, phương pháp được hiển thị như dưới đây:
Lỗi điện và các nguyên nhân thông thường



FAILURE

CAUSES

MEASUREMENT TO TAKE

Air Exhaust Temperature too high

Bad vent condition, Oil lacking etc.

Check the vent condition and lubricant amount etc.

Temperature Sensor Failure

Cable off or PT1OO damaged

Checking the wiring and PT100

Over Pressure

The pressure too high or the pressure sensor failure

Check the pressure and the pressure sensor

Pressure Sensor Failure

Cable off, Sensor damaged or the cable connected reversed

Check the wiring and sensor transformer

Water Lacking

Water Pressure switch damaged

Check the water pressure switch

Phase Lacking

Power phase lacking or the Contactor terminal damaged

Check the power and contactors

Overloaded

Voltage too low, tubes blocked, Bearing Wear off or other mechanical failure or wrong set data etc.

Check the set data, Voltage, bearings, tubes and other mechanical systems.

Unbalance

Power unbalance, Contactor damaged or the internal open of the motor

Check the power, contactors and the motor

Rotor Lock

Voltage too low, tubes blocked, Bearing Wear off or other mechanical failure or wrong set data etc.

Check the set data, Voltage, bearings, tubes and other mechanical systems.

Short Circuit

Wrong Wiring, Incorrect Data setting etc.

Checking the wiring and set the data correctly

Wrong Phase Sequence

Reversed Phase sequence or phase off

Check the wiring

Fan stopped

Fan damaged, Contactor damaged, no control output

Check the wiring and control output

Overload or Rotor locking during starting process

Host start time set to a value less than the star angel time delay

Reset the host starting time to be longer than star angel delay + Load delay time

The main Contactor activate time to time

The emergency button loose

Check the wiring

  • TEL:+ 86-021-67150020
  • FAX:+ 86-021-67150020
  • EMAIL:Sales@rotorcompressor.com
  • ADDRESS:No.28 Minta Road, Quận Songjiang Thượng Hải, Trung Quốc